sapstill.blogg.se - Behringer x32 usb drive playback

#Behringer x32 usb drive playback drivers
#Behringer x32 usb drive playback driver
#Behringer x32 usb drive playback software
#Behringer x32 usb drive playback Pc

However, I am aware that with all production lines there can always be faults with some units ( e.g when you buy a new car one would usually do a pre-delivery inspection). This will change the send TAP point from the Main LR or Mix Busses to the Matrix to PRE FADER which will allow you to freely lower the LR mix or Busses without adjusting the stream level.I have yet to receive my x32 – hopefully next week.įrom the spec and what others have said I think it will be a great product - and am looking forward to getting it. Rotate the 1 st encoder counterclockwise and select PRE.

Press the DOWN arrow (Layer Down) button to expose the Mode 1-2, Mode 3-4 and Mode 5-6 options above the 1 st, 3 rd and 5 th encoder.

This step is sending your mix to the matrix channels (matrix channels which you’ve already assigned to the USB Outputs 1-2). They should raise together as they are linked.

Now that you have either your pair of busses or your Main Mix ready to be sent out to the stream, SELECT either the Main LR or MIX BUS 1.

To send signal to the busses you can use the SENDS ON FADER feature or the HOME>SENDS menu with your channels selected.

Now create your stream mix using the selected busses.

Open the HOME menu and hit the LINK button to LINK busses 1 and 2. If you choose to run a complete separate mix, select two mix busses (for example, 1 and 2) SELECT BUS 1. You will have to decide if you want the mix going out to your stream to be identical to the Main Mix (the House mix) or if you need it to be a separate mix. Open the HOME menu and press the LINK button (1 st encoder) to link MATRIX 1 and MATRIX 2 as an LR pair.

On the surface of your X32, select MATRIX 1.

Repeat for Output 2 (02 and MATRIX 2, POST FADER.

Highlight output 1 (01 With 01 highlighted, use the 4 th column (OUT SIGNAL) to select MATRIX 1, and use the 5 th column (TAP) to select POST FADER The left most column in this menu is the option to select which output “pathway” you are working with.

Navigate to the P16 page (OUT, if using the OUTPUT 1-8 option because you have a P16 system in use).

You will notice that on the right side of the menu you can see a breakdown of which signals are routed to the outputs.

If you are using a P16 system you should assign OUTPUT 1-8).

In the first column (1-8) assign P16 1-8 (this is assuming you are NOT using a P16 system for monitoring purposes.

Open the ROUTING menu on your X32 and Navigate to the CARD tab.

In order to do this, follow the process below.

#Behringer x32 usb drive playback software

Typically with streaming software, the software will only look at the first two channels coming in via USB from the mixer, so it will be important to send the mix that you want to the first two USB Outputs on the mixer, so that your streaming software receives the right information. Select the Expansion card as the input device. You should also see the expansion card as an input option with your streaming software (OBS, FB Live, YouTube etc).

#Behringer x32 usb drive playback Pc

Now, after connecting via USB to your computer from the expansion card, you should see that your Mac or PC recognizes that the expansion card has been connected and you should have options within your operating system’s sound settings to choose the X-USB, X-UF or X-LIVE as your Playback or Recording device.

#Behringer x32 usb drive playback drivers

You can find the downloads for all of the X32 drivers at:

#Behringer x32 usb drive playback driver

Select the driver that matches your expansion card (X-USB, X-UF, X-LIVE) There are multiple drivers available but that is because they are for the different expansion cards. This guide is intended to assist with setting up a stereo output stream from your X32 to a streaming software like OBS or FB Live.įirst, if you are using a PC make sure you have the proper driver installed. X32 – How do I Setup for Live Streaming with V4 firmware?